Hoppa till innehåll
Free shipping on orders over 3000 SEK excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The fridge failed on Friday evening and no one noticed until Monday morningLegionella control that doesn’t end up in a binder: timestamped temperatures straight from the tapMoisture that isn’t visible on the surface becomes most expensive when it’s discovered after the floor is laidA Surface That Looks Clean Can Still Be Dirty: How ATP Measurement Shows the Result in Ten SecondsStop guessing the salt in your brine: read the concentration in a few secondsThree known temperature points are enough to tell whether your thermometer still reads correctlyHow to Know Your Thermometer Still Reads Correctly: Checking Type K Instruments at Three Known PointsOne drop is enough to see whether the coolant concentration is correct, without interpreting a borderline by eyeA spot check doesn’t tell you what happened in the cold room overnight between two inspectionsHow to Measure Small, Hot Surfaces from a Safe Distance Without GuessingVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The fridge failed on Friday evening and no one noticed until Monday morningLegionella control that doesn’t end up in a binder: timestamped temperatures straight from the tapMoisture that isn’t visible on the surface becomes most expensive when it’s discovered after the floor is laidA Surface That Looks Clean Can Still Be Dirty: How ATP Measurement Shows the Result in Ten SecondsStop guessing the salt in your brine: read the concentration in a few secondsThree known temperature points are enough to tell whether your thermometer still reads correctlyHow to Know Your Thermometer Still Reads Correctly: Checking Type K Instruments at Three Known PointsOne drop is enough to see whether the coolant concentration is correct, without interpreting a borderline by eyeA spot check doesn’t tell you what happened in the cold room overnight between two inspectionsHow to Measure Small, Hot Surfaces from a Safe Distance Without Guessing

ETI DishTemp dishwasher temperature meter: How a Ø127 mm plastic plate with a built-in sensor verifies that your dishwasher reaches the HACCP-mandated 71 °C for at least 1 second

Published 11 July 2026 at 22:15

A health inspector from the environmental health department arrives at a restaurant for a HACCP inspection. One of the critical control points is the dishwasher. They want to see DOCUMENTATION that the rinse-phase temperature is at least 71 °C, measured daily. The restaurant’s owner shows their logbook with thermometer strip readings for the past 30 days. The inspector dismisses them: ”Test strips aren’t precise enough. What do you use to verify the cycle?”

The restaurant has four options: (1) ignore the problem and risk a fine, (2) buy more expensive thermometer systems that require operator integration, (3) hire an external consulting firm for monthly verifications (SEK 5,000-10,000/year), or (4) buy an ETI DishTemp for SEK 708, which runs through the dishwasher like a real plate and shows the exact maximum temperature.

DishTemp is designed specifically for this niche, HACCP verification of commercial dishwashers, and solves the problem with a simple elegance that conventional thermometers can’t match.

HACCP requirements for dishwasher temperature

HACCP (Hazard Analysis and Critical Control Points) is an international food safety standard, mandatory in the EU, the US, the UK and most OECD countries. The dishwasher requirement is based on microbiological studies of bacterial kill rates:

  • Salmonella: Killed at 65 °C in 4 seconds, or 60 °C in 10 minutes.
  • Listeria monocytogenes: Killed at 70 °C in 2 minutes, or 75 °C in 15 seconds.
  • Campylobacter: Killed at 55 °C in 1 minute.
  • E. coli: Killed at 70 °C in 1 minute, or 75 °C in 15 seconds.
  • Norovirus: Requires 71 °C for 10 seconds, or 82 °C for 5 seconds.

Practical threshold values:

  • UK standard (Environmental Health): The final rinse must reach 71 °C for at least 1 second.
  • EU standard (EN 15883-1): The final rinse must reach 82 °C for at least 1 second for automatic dishwashers without chemical disinfectant.
  • US FDA standard: 74 °C recommended, minimum 71 °C for 30 seconds or 82 °C for 10 seconds.

71 °C is precisely the CRITICAL MEASUREMENT POINT for which DishTemp is supplied with a calibration certificate. The instrument is final-calibrated at exactly this reference point.

What DishTemp physically is

DishTemp is a Ø 127 mm × 14 mm thick ABS plastic disc that looks and behaves like a real plate in the dishwasher. Inside the disc are:

  • A temperature sensor (typically an NTC thermistor or PT type).
  • A lithium battery (CR2032 3 V coin cell).
  • A small LCD display visible on one side.
  • A simple microprocessor with a max-hold function.
  • An IP66-sealed enclosure (resistant to water pressure and dust).

Total weight: 120 grams, comparable to a real porcelain plate. The dishwasher’s water flow pattern and heat transfer are simulated accurately because the disc has similar dimensions and thermal mass to real plates.

Workflow: measuring one cycle

  1. Activate DishTemp by pressing the ”ON” button.
  2. The instrument shows the starting temperature (typically room temperature, ~22 °C).
  3. Place DishTemp in the dishwasher like a real plate, in the plate rack, LCD side up.
  4. Start the dishwasher cycle as normal.
  5. After the cycle (typically 90-180 seconds): remove DishTemp.
  6. Read the MAX temperature on the LCD display. It resets automatically the next time ”ON” is pressed.
  7. Record the value in the HACCP logbook.

Total time for one verification cycle: ~5 minutes including waiting time. With daily HACCP checks: 15-20 minutes of work per week in total.

Accuracy assessment

ETI DishTemp has:

  • Measuring range: 0-90 °C. Sufficient for all dishwasher verification.
  • Resolution: 0.1 °C.
  • Accuracy: ±0.5 °C.
  • Calibration: factory-calibrated at 71 °C with a free traceable certificate.

The critical question: is ±0.5 °C accuracy sufficient for HACCP verification? Yes. If the HACCP threshold is 71 °C and DishTemp shows 71.3 °C, the actual temperature is 70.8-71.8 °C. The safety margin is built into the HACCP threshold itself (i.e. 71 °C is a lower limit with a built-in safety margin above the biologically lethal 65-70 °C).

For documentation in borderline cases, the operator should keep a margin of a couple of degrees above the threshold. Measure a consistent 74-75 °C and you are safe even with ±0.5 °C of uncertainty.

ETI DishTemp smart thermometer for dishwashers Ø127 mm plate simulator

Alternatives to DishTemp, and why they don’t work well

Thermometer strips (single-use strips with heat-sensitive ink): SEK 20-50 per strip. Stuck onto a plate. The ink changes color at the threshold temperature.

  • Drawback 1: Accuracy typically ±2-3 °C.
  • Drawback 2: Adheres poorly to wet surfaces.
  • Drawback 3: Single-use, so 30 strips per month = SEK 600-1,500/year.
  • Drawback 4: Inspectors no longer accept the result as HACCP documentation.

Thermocouple with the probe taped to a plate: SEK 500-1,500 for the instrument plus probes.

  • Drawback 1: The tape doesn’t hold up against the dishwasher’s water pressure.
  • Drawback 2: The probe measures air or tape temperature, not the plate surface.
  • Drawback 3: Routing the cable through the dishwasher door creates complications.

Thermometer wax tablets: SEK 5-15 per tablet. Melt at a known temperature.

  • Drawback 1: Gives only ”above/below” information, no exact value.
  • Drawback 2: Single-use.
  • Drawback 3: Melted wax can contaminate the dishwashing system.

DishTemp (this one): SEK 708 once, 5,000 hours of battery life (~5 years of daily use), IP66, exact reading ±0.5 °C.

Total annual cost: practically zero after purchase. Compared with SEK 600-1,500/year for single-use methods, it pays for itself within a year.

Other applications beyond the dishwasher

DishTemp is designed specifically for dishwashers but also works for:

Oven verification: Place it on a plate run through a heating cycle. Verify that specific temperatures are reached.

Refrigerator verification: Long-term measurement of cold chains. Battery life is enough for several days of continuous recording.

Sterilization tests: Autoclaves for medical instruments.

Washing machine verification: Where hot-water rinsing is required (e.g. professional laundries handling healthcare textiles).

Equipment testing: On delivery of new kitchen equipment, to verify the performance specification.

Limitations

  • Max-hold only, no time profile: Shows the highest temperature but not HOW LONG it lasted. HACCP requirements such as ”71 °C for 30 seconds” can’t be verified directly with DishTemp. You assume that if the max was reached, the threshold must have been exceeded for a short time.
  • Single-point measurement: Measures at one position at plate size. If some corners of the rack get a lower temperature than DishTemp’s position, it won’t be detected.
  • No data storage across cycles: Must be noted manually after each cycle.
  • Replaceable battery, but it’s a 5-minute job: After 5,000 hours (typically 5 years of daily use) the battery needs replacing. The CR2032 coin battery is standard and inexpensive.
  • No connection to HACCP software: Manual entry in the logbook. Larger chains with automated reporting need more advanced equipment.

Who needs DishTemp

Restaurants and cafés: Daily HACCP verification as part of standard QC.

Canteens and commercial kitchens: Schools, hospitals, elder care, where health regulations are strict.

Childcare and preschools: Where very young children are especially vulnerable to gastrointestinal infections.

Hotels and conference facilities: Room service and restaurant kitchens.

Food industry: Where products pass through processes with sanitation steps.

Environmental and health authorities: For field inspections. Easy to carry in an inspector’s tool bag.

Dishwasher service technicians: During installation and maintenance, to verify that the machine delivers its specified performance.

Facility management for larger buildings: Regular verification of all kitchens in the building portfolio.

What you get for your money

ETI DishTemp dishwasher thermometer, measuring range 0-90 °C, resolution 0.1 °C, accuracy ±0.5 °C, IP66 waterproof, LCD display with max-hold function, ABS plastic plate shape (Ø 127 mm × 14 mm, 120 g), CR2032 lithium battery with 5,000 hours of life, reusable over hundreds of cycles, free traceable calibration certificate at 71 °C (the critical HACCP threshold), Celsius/Fahrenheit switching, 1-year warranty. SEK 708.

The standard tool for restaurants, commercial kitchens, hotels and other food businesses that are subject to HACCP requirements for dishwasher verification. It pays for itself through saved single-use test strips within 6-12 months. The simplest possible workflow: run it like a plate, read it, note it in the logbook. The free certificate immediately completes the documentation requirement. Larger chains with hundreds of wash cycles daily may need more advanced automated systems, but for individual restaurants and canteens, DishTemp is the economic and practical sweet spot.

Read more: ETI DishTemp dishwasher thermometer in the shop →

More news

All news