Published 15 July 2026 at 09:47
The dry-block calibrator is a fundamental piece of infrastructure in any laboratory or business that needs to calibrate its own thermometers periodically. The concept is simple: an aluminum block with precisely drilled holes in standard sizes, electronically controlled to a programmable temperature. Place the test thermometer’s probe in the hole, wait for it to stabilize, and compare it with the displayed block temperature.
Together with the Precision Plus PT100 reference thermometer (as described in our earlier article), the dry-block calibrator forms a complete INTERNAL CALIBRATION SYSTEM that can verify a business’s entire thermometer fleet without an external calibration lab.
The physics of dry-block technology
The dry-block calibrator consists of three main components:
- Aluminum block: Solid aluminum (typically 500-1500 grams) with precisely drilled holes. Aluminum is chosen for its high thermal conductivity (237 W/m·K), which gives an even temperature throughout the block within 1-2 minutes.
- Resistive heating element: Nichrome wire around or under the block. Electronically controlled by a PID controller (Proportional-Integral-Derivative).
- Integrated reference thermometer: A factory-calibrated Pt100 or thermistor inside the block. It shows the ACTUAL block temperature on the display.
When the operator sets the desired temperature, the PID controller activates the heating element. The aluminum block heats up with a controlled ramp. After ~5 minutes, the block has stabilized to within ±0.5 °C of the setpoint.
The test thermometer’s probe is placed in a hole of matching size. The tip of the probe reaches the block temperature after a further 30-60 seconds (thermal conduction from the aluminum to the probe metal). The test thermometer’s reading is then compared with the displayed block temperature.
Hole size standards
Model 3001 accepts probe sizes of Ø3.3, 4, 4.76 and 6.35 mm. These are STANDARD diameters for commercial temperature probes:
- Ø3.3 mm: Slim needle probes (ThermaLite, Thermapen ONE).
- Ø4 mm: Medium-thickness probes (NTC thermistor probes).
- Ø4.76 mm (3/16″): Standard-thickness probes (many industrial probes).
- Ø6.35 mm (1/4″): Robust probes (BBQ, industrial process, oven monitoring).
If a probe of a completely different size needs to be calibrated, the following are available:
- Model 3002: Ø3.3 / 4.76 / 6.35 / 9.6 mm.
- Model 3003: Ø4.76 and 12.7 mm (1/2″ — for heavy-duty industrial probes).
The 33-250 °C temperature range
Model 3001’s heating range starts at 33 °C — just above room temperature. It CANNOT be used for cold calibration (below 33 °C). For cold-chain work, you will need one of the following:
- A fixed-point reference (ice water for 0 °C).
- A Peltier dry block with active cooling (models in the 2,000-15,000 kr range, such as the Fluke 9142).
- An insulated bath with a thermostat (more general lab technique).
The 250 °C maximum covers most applications other than industrial furnace control:
- Cold chain: -25 to +8 °C (outside this instrument’s range).
- Food production: 60-100 °C (well covered).
- Baking/roasting: 150-250 °C (covered).
- Furnace annealing: 400-800 °C (outside).
- Chemical synthesis: 20-250 °C (covered).
±0.5 °C stability: what it means for calibration uncertainty
The ±0.5 °C stability is the DOMINANT SOURCE OF ERROR in standard dry-block calibration. The combined calibration uncertainty is:
U = √(U_stability² + U_gradient² + U_ref-thermometer²)
For model 3001:
- U_stability ≈ 0.5 °C.
- U_gradient (vertical temperature gradient in the block hole): 0.05-0.15 °C.
- U_ref-thermometer (factory-calibrated internal sensor): 0.15 °C.
Combined: U ≈ √(0.25 + 0.02 + 0.02) = 0.54 °C.
This means a test thermometer can be calibrated to ±1 °C uncertainty in the 33-250 °C range — good enough for HACCP in the food industry, laboratory operations, and most industrial QC applications.
For BETTER precision (necessary for pharmaceuticals and aerospace), you will need a Fluke 9142 (±0.1 °C stability, cost 50,000+ kr) or reference cells with fixed-point standards.
Metallic Equalizing Block (MEB) — hole inserts
The standard holes in the dry block are round, with some clearance for probe insertion. This clearance creates extra thermal resistance that degrades calibration precision.
Optional accessory: MEBs (Metallic Equalizing Blocks) are small aluminum hole inserts with EXACTLY matched inner diameters for specific probe sizes. The insert fills the gap between the block hole and the probe, providing better thermal contact.
Meta-studies show a 20-30% improvement in calibration uncertainty with an MEB versus without.
Calibration workflow
Standard practice for calibrating a routine thermometer:
- Switch on the calibrator and let it run for 15-30 minutes so the housing electronics can reach thermal stability.
- Program the desired calibration temperature (e.g. 50 °C).
- Wait 5 minutes for the block to stabilize.
- Verify the block temperature against a reference thermometer (Precision Plus PT100) placed in the secondary hole.
- Place the test thermometer in the primary hole.
- Wait 30-60 seconds for the probe to reach thermal equilibrium.
- Read the test thermometer’s display.
- Calculate the deviation: (test thermometer) − (reference thermometer). Record it in the calibration log.
- Repeat at the next calibration temperature (e.g. 100 °C, 150 °C, 200 °C).
- A 4-point calibration curve gives a good characterization of the test thermometer’s linearity.
Total time for a 4-point calibration: 30-60 minutes per test thermometer.
Economic analysis
Without a dry-block calibrator (external calibration per instrument):
- 10 thermometers × 1500 kr per external calibration = 15,000 kr per year.
- Thermometers away from the business for 2-3 weeks per year.
- Spare instruments required.
With a dry-block calibrator (internal calibration):
- Calibrator purchase: 22,080 kr.
- Precision Plus reference thermometer (see article): 3,460 kr.
- Annual re-certification of calibrator and reference: 3,000-5,000 kr.
- No external calibration of routine instruments.
- First-year total: ~26,000 kr.
- After the first year: 3,000-5,000 kr per year.
Breakeven time: approximately 2 years with 10 instruments. After that, internal calibration is dramatically more economical. For larger businesses (20+ thermometers), breakeven comes in under a year.
Calibration certificate included
Model 3001 is delivered with a calibration certificate that verifies the accuracy of the block temperature at several reference points. The standard certificate covers 3-5 points across the entire operating range.
Certificate validity period: 12 months. Annual re-verification is required to maintain formal calibration status.
Applications
Food industry: Standard internal calibration of all HACCP thermometers. Without internal calibration, external lab services are unavoidable.
Pharmaceutical production: GxP requirements call for annual verification of all temperature instruments. An internal calibration lab saves time and reduces exposure.
Clinical laboratory: Calibration of blood gas analyzer thermometers and autoclave verification probes.
Calibration service companies: Companies that offer calibration services use this as a WORKING TOOL.
Universities and research: Scientific laboratory maintenance.
HVAC service: Calibration of service thermometers used for air-conditioning inspections.
Chemical industry: Process thermometer verification in production plants.
Breweries: Calibration of fermentation and storage temperature loggers.
Education: Vocational schools and technical colleges use it as a demonstration tool for metrology education.
Comparison with alternatives
Simple ice-water bath (free): 0 °C point only. Good for ice-point verification, not for multiple points.
Boiling water + pressure compensation (almost free): ~99-100 °C point. Adjusted for local air pressure. Single point only.
ETI Calibrator 3001 (this one, 22,080 kr): 33-250 °C multi-point. Good for standard industrial calibration. ±0.5 °C stability.
Fluke 9142 (~55,000 kr): -25 to +150 °C, ±0.1 °C stability. Covers cold chain + heat.
Isotech Peltier dry block (~30,000-80,000 kr): -30 to +160 °C, Peltier-driven cold + hot.
Fixed-point cells (5,000-30,000 kr per cell): The fundamental reference for ITS-90 traceability (gallium, indium, tin freezing points). For calibration labs only.
Fluid bath with thermostat (10,000-40,000 kr): Better precision in certain ranges, but more complex to operate.
Specifications
- Model: ETI 3001 dry-block calibrator.
- Temperature range: 33-250 °C.
- Resolution: 0.1 °C.
- Stability: ±0.5 °C.
- Stabilization time: ~5 minutes.
- Hole sizes: Ø3.3, 4, 4.76, 6.35 mm.
- Material: aluminum block.
- Electronics: PID controller.
- Integrated internal reference thermometer.
- Display: LCD with programmable temperature setpoint.
- Calibration certificate included (3-5 points).
- MEB inserts available as an accessory for specific probe sizes.
What you get for your money
ETI Calibrator model 3001 dry-block heat source, temperature range 33-250 °C, resolution 0.1 °C, stability ±0.5 °C, stabilization time ~5 minutes, hole sizes Ø3.3 / 4 / 4.76 / 6.35 mm, integrated internal reference thermometer, PID electronics, LCD display, calibration certificate included. 22,080 kr.
The standard instrument for internal calibration labs in the food industry, pharmaceutical production, clinical laboratories, calibration service companies, HVAC service, and other businesses with 10+ thermometers that must be verified periodically. The premium over ”external calibration per instrument” is justified by the investment paying for itself within 1-2 years and by dramatically reduced equipment downtime.
Read more: ETI Calibrator 3001 in the shop →