Hoppa till innehåll
Free shipping on orders over 3000 SEK excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The surface shows one temperature, the core another: why you need both IR and a penetration probeThe temperature in the warehouse changes overnight, and nobody notices until MondayThe freezer was warm last night, but nobody knows for how long: this is how the max and min values show what happenedThe Temperature Drop Across a Radiator Tells You More Than Two Separate ReadingsOne Second Instead of Ten: How Response Time Affects Both Quality and Self-InspectionAir temperature in the fridge doesn’t tell you how warm the product isThe fridge failed on Friday evening and no one noticed until Monday morningLegionella control that doesn’t end up in a binder: timestamped temperatures straight from the tapMoisture that isn’t visible on the surface becomes most expensive when it’s discovered after the floor is laidA Surface That Looks Clean Can Still Be Dirty: How ATP Measurement Shows the Result in Ten SecondsVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%The surface shows one temperature, the core another: why you need both IR and a penetration probeThe temperature in the warehouse changes overnight, and nobody notices until MondayThe freezer was warm last night, but nobody knows for how long: this is how the max and min values show what happenedThe Temperature Drop Across a Radiator Tells You More Than Two Separate ReadingsOne Second Instead of Ten: How Response Time Affects Both Quality and Self-InspectionAir temperature in the fridge doesn’t tell you how warm the product isThe fridge failed on Friday evening and no one noticed until Monday morningLegionella control that doesn’t end up in a binder: timestamped temperatures straight from the tapMoisture that isn’t visible on the surface becomes most expensive when it’s discovered after the floor is laidA Surface That Looks Clean Can Still Be Dirty: How ATP Measurement Shows the Result in Ten Seconds

The surface shows one temperature, the core another: why you need both IR and a penetration probe

Published 22 November 2026 at 11:59

You point an IR thermometer at a chilled pallet, a bearing housing or a pipe bend and get a reading immediately. Then the doubt sets in: is it the surface being measured or the product itself, and does the value match what a contact probe would show? Many workshops and kitchens therefore keep two instruments in the drawer and make full use of neither.

ETI RayTemp® 8 Kit, thermometer for both IR and penetration measurement, supplied with penetration probe, cleaning wipes and carrying case

Two measuring principles in one instrument

RayTemp 8 is a pistol-shaped infrared thermometer with a laser spot and a distance-to-spot ratio of 12:1. The IR range is -60 to 500 °C. The instrument also has a socket for a type K miniature connector, so you can connect a thermocouple probe and measure in air, liquid or material. With the probe’s range, measurement can extend from -64 to 1370 °C. The kit includes a penetration probe, 100 antibacterial probe wipes and an ABS carrying case.

What problems does it solve?

IR measurement is fast and requires no contact, but it only shows the temperature of the surface. Shiny metal surfaces can also give incorrect readings because they emit radiation poorly. The penetration probe gives you the value you can document and compare. With both in the same instrument, you use IR to find the deviation and the probe to confirm it. The max, min, difference and average functions let you see the spread across a surface or a series of measuring points without writing notes on paper.

Three situations where it is used

Maintenance and electronics. Point the IR thermometer at fuses, terminal blocks and motor housings in a live installation. A terminal that is ten degrees warmer than its neighbors is often a poor screw connection that should be fixed before the next stop.

Food production. At goods receiving, you check the surface of an entire load of chilled goods in a few seconds. If any value deviates, you insert the probe into the product and get the core temperature that your self-inspection routines require. The probe wipes mean the same probe can be used between different products.

Installation and workshop. On heating systems and sanitary installations, you compare supply and return with the IR gun, and use the probe when you need to measure air or liquid directly.

Why it pays off

One kit replaces two separate instruments, and you avoid keeping track of two sets of batteries, cases and calibration routines. The biggest gain is still time. Screening with IR takes seconds per point, and contact measurement is used only where it is needed. A fault discovered as a hot outlet or a chilled product a few degrees too warm costs far less than a breakdown or a discarded batch.

If you want an instrument that covers both surface and core, the RayTemp 8 Kit is available from us. See the product here.

Read more

More news

All news